4-Channel Encoder Motor Driver with Onboard Voltage Regulation Circuit for Motor Control Intelligent Small Car
- 【Drive Multiple Motors】The 4-channel encoder motor driver can drive a variety of Hall encoder TT motors and 520/310 DC gear motors available in the market.
- 【Support Various Controllers】The 4-channel encoder motor driver is compatible with STM32, Arduino microcontrollers, Raspberry Pi 5/4B, Jetson Nano, and other controllers.
- 【High-performance Motor Driver Chip】The 4-channel encoder motor driver features the SA8339 high-performance motor driver chip. Ideal for electronic competitions and DIY robot cars, it offers versatility and reliability.
| Product Parameter | |||
| Motor driver chip | SA8339 | VM power supply range | 5-15V |
| Power output | VM, 5V, 3.3V | 5V output current | 1A |
| Hall signal logic output voltage | 3.3V, 5V | Expansion board protection function | Input reverse connection protection |
| Single channel rated drive current | 2A | Single channel maximum peak | 2.5A |
| Product Parameter | |
| Motor driver chip | SA8339 |
| VM power supply range | 5-15V |
| Power output | VM, 5V, 3.3V |
| 5V output current | 1A |
| Hall signal logic output voltage | 3.3V, 5V |
| Expansion board protection function | Input reverse connection protection |
| Single channel rated drive current | 2A |
| Single channel maximum peak | 2.5A |
| PIN Function | |||||
| Port type | Symbol | Function | Port Type | Symbol | Function |
| Encoder | GND | Hall power supply negative electrode | IIC port | SCL | Clock line |
| A | A-phase pulse signal output terminal | SDA | Bidirectional data cable | ||
| B | B-phase pulse signal output terminal | GND | Power ground wire | ||
| VCC | Hall power positive electrode | 5V | 5V DC output | ||
| M+ | Motor power positive electrode | 3PIN power port | - | Power negative electrode | |
| M- | Motor power negative electrode | + | Power positive electrode | ||
| Power supply port | + | Power positive electrode | nc | Empty | |
| - | Power negative electrode | ||||
| PIN Function | ||
| Port type | Symbol | Function |
| Encoder | GND | Hall power supply negative electrode |
| A | A-phase pulse signal output terminal | |
| B | B-phase pulse signal output terminal | |
| VCC | Hall power positive electrode | |
| M+ | Motor power positive electrode | |
| M- | Motor power negative electrode | |
| IIC port | SCL | Clock line |
| SDA | Bidirectional data cable | |
| GND | Power ground wire | |
| 5V | 5V DC output | |
| 3PIN power port | - | Power negative electrode |
| + | Power positive electrode | |
| nc | Empty | |
| Power supply port | + | Power positive electrode |
| - | Power negative electrode | |
| Item | Specification |
| Motor driver chip | SA8339 |
| VM power supply range | 5-15V |
| Power output | VM, 5V, 3.3V |
| 5V output current | 1A |
| Hall signal logic output voltage | 3.3V, 5V |
| Expansion board protection function | Input reverse connection protection |
| Single channel rated drive current | 2A |
| Single channel maximum peak | 2.5A |
Questions & Answers
Have a Question?
-
What's the use of the GND, TX, RX, 5V pins just behind the i2c port?
Hello,
Currently, the RX and TX pins have no assigned function, while the remaining two pins (5V and GND) can be used to power other development boards.
-
I need to connect the i2c port to an 3.3V MCU, like the ESP32. What are my options? - A level converter - Connect the 3.3V port from the ESP32 to the VCC in the i2c port of this board.
1. Power the encoder motor driver module separately, selecting the voltage according to the motor being used.
2. Connect the GND, SDA, and SCL pins from the I2C to the ESP32.
3. Finally, connect the 5V pin from the encoder motor driver module to the VIN pin on the ESP32.
Note: The 5V pin on the I2C of the encoder motor driver module only supports input and does not support output.
-
What is the connector type for the 3-pin power connector?
Hello,
The diagram below illustrates the type of cable that connects to the specific port:
-
What is the cable type and size for the 4-CH motor encoder wires?
Hello,
The diagram below illustrates the type of cable that connects to the specific port:
-
4 Channel encoder motor board. What type of connector is used for the IIC Port? It seems to be different the motor connection ports
The connector type is 5264-4AW.
-
what are the registers to write to to control the motors in i2c
Hi there, pls check this tutorial: https://www.hiwonder.com.cn/store/learn/142.html
-
where's the code for this board (4-Channel Encoder Motor Driver with Onboard Voltage Regulation Circuit for Motor Control Intelligent Small Car)? I need to verify that it has documentation with either example Arduino code or better python code from RPi.
Hello. Only tutorials are provided now: https://drive.google.com/file/d/19BFlVI4pYvOb_Tf3MHPpHsck3rE9Yzpv/view?usp=sharing
-
Is there an explanation of the i2c control protocol for this driver?
Pls check this link: https://drive.google.com/drive/folders/1jl1zD6l6T0Y_1_luHWfjwjTx88PBPj75?usp=sharing
Related items
